Witty share charging station up to 22kW, OCPP for load management, RFID, calibration law. Wallbox charging station ER (calibration law compliant) with UV-resistant plastic housing for charging electric or plug-in hybrid vehicles. Charging mode Mode 3 according to DIN EN IEC 61851-1 (VDE 0122-1) via Mode 3 socket type 2, fused via the supply line of the charging station 32 A (3-phase). Permanently installed charging station for indoor/outdoor use. Free use or access authorization via RFID authentication. Consisting of a wall housing, cable entry for power supply, brightness sensor, RFID reader (sensor, precise user assignment), LED display (status, charge level, errors), MID counter (energy recording), public key for checking the charging process and charging controller with display. The charging controller forms a digital automatic signature. The operating mode (1 or 3 phase) and the charging current (10 - 32 A) are set in the integrated charging controller. The charging station is connected to a backend system for monitoring and billing via the OCPP protocol. Commissioning is carried out via the embedded web server via Wifi or Ethernet. The optional load manager (LM) allows several charging stations to be networked with one another. Load management supports both static and dynamic load management with integrated direct measurement or direct converter connection. The power supply to the charging station must have a separate circuit. Connecting multiple charging stations to the same circuit is not permitted. Each charging station must be protected with a combined residual current / circuit breaker (RCBO) type A or separately with a residual current circuit breaker (RCD) type A and a circuit breaker (MCB). A type B FI circuit breaker is not necessary as a 6 mA DC residual current detection is integrated. The charging controller is configured when used for the first time via the integrated WiFi hotspot or the LAN interface. Note: A cable holder, RFID cards and feet for free-standing installation are optionally available.
Witty share charging station up to 22kW, OCPP for load management, RFID, charging socket. Wallbox charging station with UV-resistant plastic housing for charging electric or plug-in hybrid vehicles. Charging mode Mode 3 according to DIN EN IEC 61851-1 (VDE 0122-1) via Mode 3 socket type 2, fused via the supply line of the charging station 32 A (3-phase). Permanently installed charging station for indoor/outdoor use. Free use or access authorization via RFID authentication. Consisting of a wall housing, cable entry for power supply, brightness sensor, RFID reader (sensor) and LED display (status, charge level, error). The operating mode (1 or 3 phase) and the charging current (10 - 32 A) are set in the integrated charging controller. The charging station is connected to a backend system for monitoring and billing via the OCPP protocol. Commissioning is carried out via the embedded web server via Wifi or Ethernet. The optional load manager (LM) allows several charging stations to be networked with one another. Load management supports both static and dynamic load management with integrated direct measurement or direct converter connection. The power supply to the charging station must have a separate circuit. Connecting multiple charging stations to the same circuit is not permitted. Each charging station must be protected with a combined residual current/line circuit breaker (RCBO) type A or separately with a residual current circuit breaker (RCD) type A and a line circuit breaker (MCB). A type B FI circuit breaker is not necessary as a 6 mA DC residual current detection is integrated. The charging controller is configured when used for the first time via the integrated WiFi hotspot or the LAN interface. Note: A cable holder, RFID cards and feet for free-standing installation are optionally available.
E-charging station accessory cable M3T2/T1 20A 1P 5m. Charging cable according to IEC 62196-2 for home charging stations consisting of charging cable with coupling (type 2, vehicle side) and coupling with type 1 (charging station side). Notes: Cable only compatible with Hager charging stations.
Witty start charging station 11/22kW with key switch and Type2 charging socket. Wallbox charging station with UV-resistant plastic housing for charging electric or plug-in hybrid vehicles. Charging mode Mode 3 according to EN 61851, secured via the charging station's supply line. Charging station with Mode 3 socket type 2 32 A (3-phase). Permanently installed charging station for indoor/outdoor use. Free use or access authorization via key switch possible. Consisting of a wall housing, cable entry for power supply, key switch, USB interface and LED display. The power supply to the charging station must have a separate circuit. Connecting multiple charging stations to the same circuit is not permitted. Each charging station must be protected with a combined residual current and circuit breaker (RCBO) type A or separately with a residual current circuit breaker (RCD) type A and a circuit breaker (MCB). A type B FI circuit breaker is not necessary, as 6 mA DC residual current detection is integrated. The charging controller is ready for operation when delivered, but further settings can be made via the rotary control or via the USB interface. Note: Various feet are available for free-standing installation.
Charging control witty house load limitation + PV CHP charging 3-phase. Charging control module for use with Hager charging station and for installation in the meter cabinet. The module allows the charging current of the charging station to be dynamically adjusted to the available free capacity of the house installation in order to avoid overloading. If the set limit value is exceeded, the vehicle's charging current is reduced until charging is interrupted. Alternatively, the device can also be used for the targeted charging of renewable energy (PV, CHP). For this purpose, the current transformer is attached to the feed line. After connecting a vehicle, the charging station waits until the minimum current is exceeded and then starts charging and dynamically follows the current fed in. Charging control module consisting of DIN series built-in devices with 3 converters. Possible adjustable limits for the overall installation from 15 to 100 A. Note: A two-wire connection to the charging control module in the charging station is required.
E-charging station accessories base, simple XEV1xx XEV2xx. Stand for holding Hager home charging stations made of powder-coated sheet steel housing or UV-resistant plastic housing and is used for protected cable routing and for mounting the charging stations. Consisting of a square stainless steel hollow body, powder-coated, closed at the top and a round cutout for cables. Notes Concrete foundation is carried out on site according to static specifications. Floor base is recommended.
E-charging station accessory cable M3T2/T2 20A 1P 5m. Charging cable according to IEC 62196-2 for home charging stations consisting of charging cable with coupling (type 2, vehicle side) and coupling with type 2 (charging station side). Note: Cable only compatible with Hager charging stations.
E-charging station accessory cable M3T2/T2 32A 3P 5m. Charging cable according to IEC 62196-2 for home charging stations consisting of charging cable with coupling (type 2, vehicle side) and coupling with type 2 (charging station side). Note: Cable only compatible with Hager charging stations.
E-charging station accessories double stand XEV1xx XEV2xx. Stand for holding Hager home charging stations made of powder-coated sheet steel housing or UV-resistant plastic housing and is used for protected cable routing and for mounting the charging stations. Consisting of a square stainless steel hollow body, powder-coated, closed at the top and a round cutout for cables. Notes Concrete foundation is carried out on site according to static specifications. Floor base is recommended.
E-charging station accessory cable M3T2/T2 16A 1P 5m. Charging cable according to IEC 62196-2 for home charging stations. Consisting of charging cable with coupling (type 2, vehicle side) and open cable end (charging station side) with coding according to charging mode 3. Note: Cable only compatible with Hager charging stations.
E-charging station accessory cable M3T2/T2 20A 3P 5m. Charging cable according to IEC 62196-2 for home charging stations consisting of charging cable with coupling (type 2, vehicle side) and coupling with type 2 (charging station side). Note: Cable only compatible with Hager charging stations.
E-charging station accessories floor base for XEV4xx. Floor base made of stainless steel for mounting a base for home charging stations made of powder-coated sheet steel housing or UV-resistant plastic housing. Notes: Concrete foundation is carried out on site according to static specifications.
E-charging station accessory cable M3T2/T2 16A 3P 5m. Charging cable according to IEC 62196-2 for home charging stations. Consisting of charging cable with coupling (type 2, vehicle side) and open cable end (charging station side) with coding according to charging mode 3. Note: Cable only compatible with Hager charging stations.
E-charging station accessory cable M3T2/T2 32A 3P 5m. Charging cable according to IEC 62196-2 for home charging stations. Consisting of charging cable with coupling (type 2, vehicle side) and open cable end (charging station side) with coding according to charging mode 3. Note: Cable only compatible with Hager charging stations.
Square column for charging station witty, can be equipped on both sides, color anthracite. Stand without floor base in rectangular or round design to match private charging stations witty.